New BigRed™ 4D-54 Dryer Cures All Inks at Ultra-High Rates
Written November 21, 2019
Categories: AD News, Industry News, News
Mark Vasilantone, President, Vastex, announces the company's new BigRed™ 4D-54 conveyor dryer. It features a pre-heating zone and high-efficiency air flow mapping, achieving ultra-high rates and side-to-side curing uniformity, while cooling the chamber skin, reducing noise and preventing dust contamination.
Seven inches (17.8 centimeters) narrower than its predecessor, the compact dryer is equipped with a 54-inch (137-centimeter) wide conveyor belt, dual heating zones and four infrared heaters capable of curing up to 950 plastisol printed garments per hour, 432 water-based or discharge-printed garments per hour, and 144 garments per hour printed with digital white ink.
A high-powered pre-heating zone surges ink temperatures past 300 F (149 C) within the first several inches of conveyor travel, maximizing dwell time at optimum curing temperatures and, in turn, conveyor belt speeds and dryer output.
Air intake fans located below the roof of the enclosure quietly draw ‘make-up’ air into the chamber’s double-walled shell through filtered inlets along opposite exterior sides at rates up to 560 cubic feet per minute (15.6 cubic meters per minute), serving to cool the outer shell for safety, while preheating the incoming air.
An exhaust fan located below the center of the conveyor belt draws the preheated air downward at rates up to 860 cubic feet per minute (24 cubic meters per minute), over the garment and through the belt, removing heat, moisture and contaminants from the chamber.
To accommodate each shop’s layout, the 6-inch (15.2-centimeter) diameter exhaust fan outlet rotates 360 degrees for connection to ductwork, and the control box can be located on the right (standard) or left side of the chamber.
Exhaust filters located on both sides of the conveyor prevent garment lint from entering the blower or exhaust stack. Cleaning all filters before or after each shift can be accomplished in one minute according to the company, safeguarding printed images, the equipment and the shop environment.
Exhaust flow sensors with warning lights alert operators to a clogged exhaust line, clogged filter or blower failure. Other safety features include a light tower to monitor dryer status, and a ‘cool down mode’ for powering down.
Dual digital PID temperature controls maintain accuracy to +/-1 F (+/-0.5 C).
The heaters of the new dryer carry a 15-year warranty, and feature closely spaced coils that provide high-density, medium-wavelength infrared heat for maximum cure speed without cold spots or under curing associated with conventional units.
The dryer’s capacity can be doubled, tripled or quadrupled when needs increase by adding one, two or three additional heating chambers and extending the conveyor belt.
Vasilantone says a BigRed™ 4D-30 version with a 30-inch (76-centimeter) wide conveyor belt will soon follow.
Seven inches (17.8 centimeters) narrower than its predecessor, the compact dryer is equipped with a 54-inch (137-centimeter) wide conveyor belt, dual heating zones and four infrared heaters capable of curing up to 950 plastisol printed garments per hour, 432 water-based or discharge-printed garments per hour, and 144 garments per hour printed with digital white ink.
A high-powered pre-heating zone surges ink temperatures past 300 F (149 C) within the first several inches of conveyor travel, maximizing dwell time at optimum curing temperatures and, in turn, conveyor belt speeds and dryer output.
Air intake fans located below the roof of the enclosure quietly draw ‘make-up’ air into the chamber’s double-walled shell through filtered inlets along opposite exterior sides at rates up to 560 cubic feet per minute (15.6 cubic meters per minute), serving to cool the outer shell for safety, while preheating the incoming air.
An exhaust fan located below the center of the conveyor belt draws the preheated air downward at rates up to 860 cubic feet per minute (24 cubic meters per minute), over the garment and through the belt, removing heat, moisture and contaminants from the chamber.
To accommodate each shop’s layout, the 6-inch (15.2-centimeter) diameter exhaust fan outlet rotates 360 degrees for connection to ductwork, and the control box can be located on the right (standard) or left side of the chamber.
Exhaust filters located on both sides of the conveyor prevent garment lint from entering the blower or exhaust stack. Cleaning all filters before or after each shift can be accomplished in one minute according to the company, safeguarding printed images, the equipment and the shop environment.
Exhaust flow sensors with warning lights alert operators to a clogged exhaust line, clogged filter or blower failure. Other safety features include a light tower to monitor dryer status, and a ‘cool down mode’ for powering down.
Dual digital PID temperature controls maintain accuracy to +/-1 F (+/-0.5 C).
The heaters of the new dryer carry a 15-year warranty, and feature closely spaced coils that provide high-density, medium-wavelength infrared heat for maximum cure speed without cold spots or under curing associated with conventional units.
The dryer’s capacity can be doubled, tripled or quadrupled when needs increase by adding one, two or three additional heating chambers and extending the conveyor belt.
Vasilantone says a BigRed™ 4D-30 version with a 30-inch (76-centimeter) wide conveyor belt will soon follow.
Related Content
-
Badger Group Acquisition Delivers First-Class Upgrade to Thysse’s Mailing Capabilities
-
Orbus Donates over $14,600 to Charitable Institutions in 2019
-
FLYERALARM sports Uses Kornit Avalanche Poly Pro to Deliver High-Quality, Photorealistic Sportswear
-
GMG Launches Advanced Color Solution for HP PageWide Digital Corrugated Presses
-
Empire Screen Printing Celebrates Over a Decade of the Partners in Printing Expo at 2021 Event